Front Mount Hitch Availability for 2019 RAM 2500

Question

Question:

Do you have a front hitch for my 19 Ram 2500? Can you tell me if I will need to trim the bumper fascia to install it?

asked by: Jason M

0

Expert Reply:

Yes, there actually is a front hitch option available for your 2019 RAM 2500, the Curt # C31015. There's a small portion that will need to be trimmed on your front bumper. I have attached a picture that shows where you'll need to trim along with the dimensions of the square opening.

expert reply by: Carla M

0

click to enlarge

Answer 1

EcoHitches like #306-X7900 are typically a more expensive brand than others like Draw Tite. This is mostly due to fact they are Made in the USA and only made from recycled materials (hence the name) which adds a bit of cost. They typically have…

view full answer...

Answer 2

Yes, the Curt front hitch part #C31015 that you referenced will fit your 2015 Ram 2500 Power Wagon with the factory built-in winch. We had a customer with basically your exact truck report back that it fit and worked well. I attached a picture they…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Robert, for a 5,200 lb Dexter Torflex axle like what you have we have the Dexter lift kit part #K71-724-02 which will give you a lift of 2-7/8 inches.

view full answer...

Answer 7

Thank you for the pictures! I reached out to my contact at Dexter Axle who was able to confirm that you have #11 Torflex axles so the correct lift kit is part #K71-724-02. Since yours has top mounting holes you also need the bracket kit #DX57FR for…

view full answer...

Answer 8

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Front Mount Hitch Availability for 2019 RAM 2500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching