Where Does Brake Controller Plug in on 2016 Lincoln Navigator

Question

Question:

Where does this plug in on my 2016 navigator? I have the 7way on the back from the facotry so I think it just plugs in right?

asked by: Curt

0

Expert Reply:

Yes, that's correct. To install the Curt Spectrum, part # C51170, or any brake controller you can use a custom harness to just plug it in. The harness is part # C51436.

We don't have a video that shows the location of the connector but it's too the right of the steering wheel.

expert reply by: Charles S

0

Answer 1

Installing the Prodigy P3 part #90195 is pretty easy on your 2015 Lincoln Navigator. Basically you need to remove a panel on the dash and the connector is there for you to attach to. See attached picture. A mechanic could knock it out really easily…

view full answer...

Answer 2

It seems like you may have the incorrect wiring connector and the harness in the photo is not the correct fit. For your 2015 Lincoln Navigator, the correct wiring adapter is #22292 for your Tekonsha Prodigy P3 #90195. If you have the factory 7-way or…

view full answer...

Answer 3

To install the 3 inch grommet part #F02-2106 you'd need to drill a hole that is 3-7/8 inches in diameter. The 1-1/2 inch grommet part #F02-2105 requires a 2-1/2 inch diameter hole.

view full answer...

Answer 4

In order to help prevent leaking between the grommet and tank on the Replacement Rubber Grommet for RV Black Water Tanks part #F02-2106 it would be wise to use a sealant like part #LT37467 between the two surfaces. I am not sure if this is a…

view full answer...

Answer 5

When installing the Curt Discover part #C84VV with the harness for your 2012 Ford F-150, part #C51436 all you'd have to do is plug in the controller and harness and you'd be set if you have the factory 7-way like it sounds like you do.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...