Is Lock Pin Needed for CIPA Pontoon Boat Mirror # CM01877

Question

Question:

description says lock pin not included. Which is this and where do you get it?

asked by: Jeanie S

0

Expert Reply:

The CIPA Pontoon Boat Mirror # CM01877 that you referenced has actually been re-designed and it no longer requires a lock pin for securing the mirror into its various positions. This is now accomplished using the tightening knob on the unit, which is included. No additional items are needed for full function of this mirror.

I have attached a short video review that you can check out as well.

expert reply by: Chris R

0

Answer 1

I recommend #CM01877. This mirror has the height required to get up and over the obstacles that are typically on the rails of tritoons and pontoons. It has the convex mirror face to give a nice wide field of view saving your neck from trying to look…

view full answer...

Answer 2

The Jif Marine Pontoon Boat Mirror with Mounting Bracket part #JIF72FR will fit any size rail up to 1-1/4".

view full answer...

Answer 3

The Jif Marine Pontoon Boat Mirror with Mounting Bracket part #JIF72FR is a universal fit mirror. It is designed to simply clamp onto the railing of a pontoon boat trailer. If you have this railing on your trailer then it should work well for you.…

view full answer...

Answer 4

It is possible that the CIPA Pontoon Boat Mirror - Clamp On - Black Powder Coated Aluminum #CM01877 you were looking at will interefere with your Bimini top when it is open, but that will really come down to the placement of the mirror and how tall…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Is Lock Pin Needed for CIPA Pontoon Boat Mirror # CM01877

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching