Will Lippert Ground Control TT Fit 2018 Lance 2285 Camper

Question

Question:

Would this auto level system work on a 2018 Lance 2285? I’m concerned about stress on the frame. I searched the q and a and didn’t see Lance mentioned. Thanks!

asked by: Paul E

0

Expert Reply:

Yes, the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 that you referenced would work great on your 2018 Lance 2285. I checked out your RV and it would be perfectly compatible with this system which will help make leveling your trailer very easy!

I attached a review video for this setup for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Lippert #LC672136 is the best trailer leveling kit for your Lance Travel Trailer. They have an overall weight capacity of 10,000 pounds and are straight forward to install. I have attached a video walking you through the installation process.

view full answer...

Answer 2

It does not look like you will be able to use the Lippert Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136 on your 2020 Lance 2285 travel trailer unless you switch your fold up rear steps to a set of fold in…

view full answer...

Answer 3

Yes, we do offer an auto-level system for travel trailers. It's the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System part #LC672136. In regards to installation, it would be hard to give an exact figure as install…

view full answer...

Answer 4

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer…

view full answer...

Answer 5

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm…

view full answer...

Answer 6

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is…

view full answer...

Answer 10

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 11

Yes, you can! So long as our Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel item #AM30820 is the same size and bolt pattern as what's on your Ironton trailer it can be used not only as a spare but also on your trailer…

view full answer...

Answer 12

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have…

view full answer...

Will Lippert Ground Control TT Fit 2018 Lance 2285 Camper

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching