Where to Install a Block Heater for 2010 Hyundai Santa Fe with 2.4L Engine

Question

Question:

Hi can someone please tell me where is the location to install block heater for 2010 hyundai santa fe 2.4L engine? Thx

asked by: Sharif M

0

Expert Reply:

I was able to reach out to Kat's for you and got some info that may help. On your 2010 Hyundai Santa Fe with the 2.4L engine you will install the Kat's Heaters Custom Fit Engine Block Heater part # KH11812 in the front left of the engine block. This will be the front drivers side. You will look for a small hole with a cover on it. The hole will be less than 3/4 of an inch. As you can see the heater has a clip on it to hold it in place so the hole will be close to the edge of the block so the clip can slide easily over the edge and hold it. Unfortunately there isn't a photo available of the location that I can provide for you to help you out. On the drivers side you have a couple of air intake components that you can remove that may give you more access to find the location.

expert reply by: Randy B

0

Answer 1

For your year and model the installation location is at the "front left." I have attached a chart showing this location as well. In the fit guide I put in your vehicle type and in the "Style" section selected the 2.4 Liter. The…

view full answer...

Answer 2

I checked with Kat's Heaters and for your 2011 Hyundai Santa Fe with the 3.5L engine the correct Engine Block Heater is part #KH11812. This cartridge style heater will install in the rear right (RR) position on the engine block, which is the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I checked with Kat's and the correct Kat's Heaters Custom Fit Engine Block Heater for a 2019 Kia Sportage with 2.0 or 2.4 engine is part #KH11812.

view full answer...

Answer 6

The underside of the standard 2023 Hyundai Elantra is different than the hybrid model of the 2023 Hyundai Elantra Hybrid, which is why the #DT75MR won't fit. There is a hitch designed specifically for the hybrid which has different attachment…

view full answer...

Answer 7

The cartridge to use to install the Kat's heater part #KH11812 that you referenced is on the front side of the engine on the passenger side as you face the engine with the hood up.

view full answer...

Answer 8

The Curt Trailer Hitch item #C53NR requires both drilling and cutting to install on your 2023 Hyundai Elantra. I have taken some screenshots from the instructions and attached them below to show you these steps. I have also attached a picture that…

view full answer...

Answer 9

Yes, we do. For your 2023 Hyundai Elantra sedan, I recommend the Curt Trailer Hitch item #C53NR. This hitch is confirmed to fit all models of the 2023 Elantra except for the N and N-Line trims. The Curt Trailer Hitch item #C53NR is custom fit and…

view full answer...

Answer 10

They rate the tongue weight on hitches based on how the vehicle would most likely be used. So the hitch you have that has a 500 lb tongue weight rating is designed to handle exactly 500 lbs when used in normal towing situations. So long story short,…

view full answer...

Answer 11

For your 2019 Jeep Cherokee with a 3.2 liter engine the Kat's heater part #KH11812 is the correct part you'd need. I checked with Kat's and they recommend the Left Rear or Right Rear cartridge. So basically the cartridges on the left or…

view full answer...

Where to Install a Block Heater for 2010 Hyundai Santa Fe with 2.4L Engine

Product Page this Question was Asked From

Continue Researching