Replacing Valve Cable on LaSalle Bristol RV Waste Valve # 34466N11AB96GMA

Question

Question:

How do I get the schematic for tightening the cable?

asked by: Rusty

0

Expert Reply:

The cable is a fixed length and does not allow for tightening. It is recommended that you use a gentle u-shape, s-shape or gentle 90* bend in the cable and secure it every so often with cable ties part # DW05727-25 to take up the slack that you might have remaining in the cable.

expert reply by: Randy B

0

Answer 1

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

view full answer...

Answer 2

For an RV with a currently installed Dometic Duo-Therm 59516.531 AC unit, I recommend the Advent Air for Dometic Setups, #ACDOM150. This is a 15,000 Btu replacement option that plugs directly into your current Dometic setup and works seamlessly with…

view full answer...

Answer 3

I don't see why a replacement Valterra Cable like part #TC72PB wouldn't work as a replacement for your Lasalle Bristol valve but officially it hasn't been tested so we can't say with total certainty. We've asked Valterra this in…

view full answer...

Answer 4

The valves you are seeking to replace are made by many different manufacturers and are a standard size. The function of the valve is what you want to pay attention to as there are T-handle and cable options and then of course black water versus gray…

view full answer...

Answer 5

The inside diameter of each side of the Valterra Bladex Waste Valve #T40A is 3 inches with the outside diameter being 3-1/2 inches. This is the same as your 3 inch PVC pipe. You wouldn't be able to connect the PVC pipe directly to the valve, but…

view full answer...

Answer 6

If the 3-1/2 inch diameter you mentioned is the outside diameter and the inside was 3 inch yes, the Valterra Bladex Waste Valve Body for RV Black Water Tank #T1003VPM could be used. If you needed the entire valve assembly you'd want the part…

view full answer...

Answer 7

I appreciate the photos but I"m not quite sure what you have under there in regards to pipe diameter. The black water tank valve will depend on if it is a hub connection, spigot connection and the diameter. For example, the Valterra Bladex Waste…

view full answer...

Answer 8

Yes. The Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents #MA10-04301k-v16 is the printed circuit board you need.

view full answer...

Answer 9

LaSalle Bristol doesn't make it so that you can replace much on their cable actuated waste valves besides just the handle so you would be better off just replacing the entire valve and cable system with Valterra's Black #TC372 and Gray…

view full answer...

Answer 10

Hi Robert, If you're just wanting to replace the condenser unit on the rooftop and retain use of your current air distribution box and thermostat then you'll just need to determine what style connector your current unit has. If you remove the…

view full answer...

Answer 11

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 12

Hello Lucas, I can definitely point you in the right direction. RV air conditioners are not custom fitted though, so really can't use the vehicle selection tool for this purpose. Do you happen to know what brand of air conditioner is currently on…

view full answer...

Replacing Valve Cable on LaSalle Bristol RV Waste Valve # 34466N11AB96GMA

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching