Connecting Valterra Bladex Waste Valve to 3 Inch PVC Pipe

Question

Question:

Looking at Valterra T40A - need an air tight gate valve that can be ed in an existing 3 PVC Sch40 pipe - not sure what HUB and Spigot references - Simply want to glue this into and existing 3 pvc pipe

asked by: Ken

0

Expert Reply:

The inside diameter of each side of the Valterra Bladex Waste Valve # T40A is 3 inches with the outside diameter being 3-1/2 inches. This is the same as your 3 inch PVC pipe. You wouldn't be able to connect the PVC pipe directly to the valve, but could with connectors that have an inner diameter of 3-1/2 inches.

expert reply by: Victoria B

0

Answer 1

I appreciate the photos but I"m not quite sure what you have under there in regards to pipe diameter. The black water tank valve will depend on if it is a hub connection, spigot connection and the diameter. For example, the Valterra Bladex Waste…

view full answer...

Answer 2

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

view full answer...

Answer 3

Schedule 40, 3 inch PVC pipe has an outer diameter of 3.5 inches and an inner diameter of 3 inches. The Valterra Bladex Waste Valve #T40B you referenced is designed to fit OVER a 3 inch diameter pipe so what you'd need is the spigot version to…

view full answer...

Answer 4

If the 3-1/2 inch diameter you mentioned is the outside diameter and the inside was 3 inch yes, the Valterra Bladex Waste Valve Body for RV Black Water Tank #T1003VPM could be used. If you needed the entire valve assembly you'd want the part…

view full answer...

Answer 5

The cable is a fixed length and does not allow for tightening. It is recommended that you use a gentle u-shape, s-shape or gentle 90* bend in the cable and secure it every so often with cable ties part #DW05727-25 to take up the slack that you might…

view full answer...

Answer 6

I don't see why a replacement Valterra Cable like part #TC72PB wouldn't work as a replacement for your Lasalle Bristol valve but officially it hasn't been tested so we can't say with total certainty. We've asked Valterra this in…

view full answer...

Answer 7

The Valterra Waste Valve for RV Black Water Tank , #T58 has a bayonet style connection. It will lock in to place from the four bayonet connections on one end and 3" Lugs on the other. Please see the attached image. If you are looking for…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 10

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Connecting Valterra Bladex Waste Valve to 3 Inch PVC Pipe

Product Page this Question was Asked From

Continue Researching