Does Gustafson RV LED Ceiling Light part # 277-000469-499 Come With an On/Off Switch

Question

Question:

Just wanted to confirm: does this have a built in switch or not? The pictures seem to show a switch, but the description explicitly says “no switch”. Thanks!

asked by: John

0

Expert Reply:

Yes the Gustafson RV LED Ceiling Light w/ Shade Satin Nickel part # 277-000469-499 has an on/off switch on the base of the unit. I have attached a photo and video for your reference.

expert reply by: Heather A

0

click to enlarge

Answer 1

For a pendant light with a textured black metal finish, we offer the Gustafson RV LED Pendant Light #277-000456 (15.5 inch long). This is LED, as opposed to incandescent, like the one you were checking out #277-000309, so they will shine much…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...