Replacement Red Trailer Clearance Light for 2007 Revolution RV Glo Brite 446A

Question

Question:

Can you help me find Red Marker light lens model TMG Glo Brite 446 A/R

asked by: Jerry S

1

Helpful Expert Reply:

We don't carry just a lens replacement for the Glo Brite 446 but we have the very similar Optronics LED light replacement part # MCL44RB1 for a red replacement that would work well! It's an LED and priced great too so it would be an easy solution.

expert reply by: Jameson C

1

Answer 1

In order to find the correct replacement rear clearance lights for a 2008 Fleetwood Southwind you'll need to take some measurements, note the shape and color then choose from our selection which I have attached for you below. I don't have a…

view full answer...

Answer 2

The SAE codes on the lens of a light indicate what function(s) that light can perform. Many trailer lights are designed to do more than one function. Based on the SAE codes on the first light, it performs the following functions: A - Rear reflector…

view full answer...

Answer 3

Although we don't offer a replacement lens or a clearance lamp assembly that fits those dimensions, we offer a 6 x 2 inch replacement LED clearance lamp, part #MCL76RB that would last up to 50 times longer than an incandescent lamp, would be much…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...