Adapter that Allows Curt A25 Slider 5th Wheel Hitch to Fit 2019 Ford F-350 with OEM Rail Kit

Question

Question:

Can I mount my Curt A25 slider with adapter fitted into the puck system of a F-350 Super Duty?

asked by: John B

1

Helpful Expert Reply:

Yes, you can mount your Curt A25 sliding 5th wheel hitch part # C35DR into the adapter that fits your 2019 Ford F-350. All you would need is the following:

- Adapter Rails for Curt 5th Wheel Hitch # C88KR

expert reply by: Jameson C

1

Answer 1

To use your Curt Q20 head in your 2019 Ford F-350 SuperDuty you will use the Curt 5th Wheel Round Tube Slider #C16020, which is the slider that fits in the factory pucks on your truck. The #C16020 works with Curt A16, E16, Q16, Q20, and Q24 5th-wheel…

view full answer...

Answer 2

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 8

Most standard pin boxes will not make a 90 degree turn in anything less than an 8 foot truck bed, but that is due to being too close to the cab - not the rails. You mentioned you wanted to replace the Rota-Flex with the Gen-Y hitch. Your old pin box…

view full answer...

Answer 9

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

The Trailair Rota-Flex 5th Wheel Pin Box #LC328329 you linked to is a fit for the 1621 bolt pattern pin boxes so it will not fit your Lippert Rhino Box, but you have three other options that will. The first option is the MORryde Cushioned 5th Wheel…

view full answer...

Answer 12

Thanks for reaching out, Michael! The Dexter Electric Trailer Brakes #K23-086-087-00 are compatible with 3,500 lb axles and have the standard 4-bolt pattern so if that matches the specs of your axle then this will definitely work for your…

view full answer...

Adapter that Allows Curt A25 Slider 5th Wheel Hitch to Fit 2019 Ford F-350 with OEM Rail Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching