Recovery Winch to Pull 2019 Nissan Frontier Pro4x

Question

Question:

I have another question if i may. this new winch BDW10044 i will be purchasing from you guys. The reason i wanted the other winch was it was easy disconnect with those long battery leads. Can i do the same with this winch add the easy disconnect battery leads. I plan on purchasing both front and rear hitch for my truck so i can easily move and connect the winch.

asked by: Gus

1

Helpful Expert Reply:

I have a solution for your, but it looks like your 2019 Nissan Frontier Pro4x has a weight between 4,414 and 4,567 lbs and the ComeUp Off-Road Winch # CU854768 is only recommended for recovery use on vehicles with a GVWR of up to 4000-lbs.

I would instead recommend using something like the Bulldog # BDW10044 which is recommended for recovery use with vehicles up to 5333-lbs GVWR. Since this winch does not come with a mounting plate, you'll want to use the Bulldog Winch Receiver Mounting Kit # BDW20155. This winch has the higher capacity you'll need to recover your 2019 Nissan Frontier and comes with a 100ft long 5/16" synthetic rope and plug-in remote.

expert reply by: Erik B

1

Gus

11/18/2019

I have another question if i may. this new winch BDW10044 i will be purchasing from you guys. The reason i wanted the other winch was it was easy disconnect with those long battery leads. Can i do the same with this winch add the easy disconnect battery leads. I plan on purchasing both front and rear hitch for my truck so i can easily move and connect the winch.

Reply

Erik B.

11/18/2019

In order to add the quick connect kit, you will want to use the Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 3 Gauge - 24' Long # BDW20026 , which provides you with 24' of wiring to run quick connects to your battery terminal. This can be used with the existing wiring on the Bulldog # BDW10044. I've attached the installation video for the Quick Connect Kit that should help you get everything wired up and ready to use on your 2019 Nissan Frontier PRO4X.

Reply

Answer 1

Long story short, that's not going to work for you even with a double line pull using a snatch block like the #CU881079. In reality, you need at least 1.5x the GVWR of your vehicle when it comes to winch capacity. The #BDW10044 I mentioned as a…

view full answer...

Answer 2

I spoke with my contact at ComeUp about a circuit breaker for the DV-6s Carry On Winch #CU854768 that you referenced. He confirmed that a 150 amp circuit breaker will work for this winch. You can use the Pollak Circuit Breaker, 150 Amp #PK54872PL.…

view full answer...

Answer 3

Great question! To power your ComeUp Off-Road Winch w/ Mounting Plate for 2" Hitches #CU854768 at the rear of your 2019 Ford F-150 you want to use the Bulldog Winch Rear Wiring Kit #BDW20206. This comes with a 20' lead of 2 Gauge Wire. If…

view full answer...

Answer 4

I have two options for wiring for your winch. You can go with the Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 2 Gauge - 20' Long, part #BDW20206, which comes with 20' long 2 gauge wire. If that is not long enough we do…

view full answer...

Answer 5

The 80 foot length of the ComeUp Off-Road Winch w/ Mounting Plate #CU854768 is the longest strap that can be used with it. Like the winch the rope/strap is rated for 6,000 lbs and when pulling that weight would draw up to 300 amps. ComeUp recommends…

view full answer...

Answer 6

The ComeUp DV-6s Off-Road Winch #CU854754 referenced in your question actually features a 3-pin plug. With this in mind the correct wireless remote will be the 3-Pin part #CU880609. I verified this with my contact at ComeUp. At this time the DV-6s…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...