Trailer Hitch That Fits 2020 Toyota Camry

Question

Question:

2020 Toyota Camry My local hitch supplier could not get a hitch to fit my new car.

asked by: Mark K

0

Expert Reply:

There is a trailer hitch fit for a 2020 Toyota Camry, the Curt Trailer Hitch Receiver # C11576.

expert reply by: Kyle S

0

Answer 1

Yes, Curt hitch #C11576 fits your 2019 Toyota Camry Hybrid and it weighs approximately 24-lbs. It fits all Hybrid versions, the LE, SE and XLE. Installation instruction are linked for reference. It will give you a 1-1/4-inch receiver opening with a…

view full answer...

Answer 2

To tow the lightweight kayak trailer with your 2019 Toyota Camry you will need a hitch, wiring, ball mount with ball, and a pin with clip. For the hitch, I recommend Class I Curt Trailer hitch receiver part #C11576 which is a 1-1/4" hitch…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #C11576 is the only hitch that we have for your Toyota and will offer decent ground clearance when installed on the 2020 Toyota Avalon. The receiver tube on the Curt hitch is going to sit right up under the rear…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Trailer Hitch That Fits 2020 Toyota Camry

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching