Recommended Trailer Hitch for a 2020 Ford Ranger

Question

Question:

I just got a 2020 Ford Ranger and now we need a trailer hitch and wiring to tow a trailer. What do you recommend?

asked by: Bob

0

Expert Reply:

The trailer hitch that I recommend for a 2020 Ford Ranger is the Curt Trailer Hitch Receiver part # C13417 which is a custom bolt-on fit that does not require any cutting or drilling. The process should actually only take you around 20 to 40 minutes. I have attached an install photo for you as well.

For a trailer wiring harness, the T-One Vehicle Wiring Harness part # 22124 is your best option as it does not require any splicing therefore is almost entirely plug and play. I also recommend adding the 7- and 4-Pole Trailer Connector Socket part # HM40975 which gives you both a 4 and 7-way as well as a mounting bracket though this is not required.

If the trailer has brakes, I highly recommend the Autowbrake Electric Brake Controller part # 3430001 as it installs entirely on the trailer so you don't have to modify the vehicle which there is not a plug-in option for.

expert reply by: Conner L

0

click to enlarge

Carl H.

7/29/2020

Just a follow-up question to this recommendation: why is this not listed in the chart on your site? The chart only lists Ranger years through 2012. I am looking for this also.

Reply

Jon G.

8/6/2020

All of these parts are listed as a fit for the 2020 Ford Ranger. Here is a link to the fit guide so that you can check this out on your end.

Helpful Links

vehicle/2020/ford/ranger

Reply

Carl H.

8/7/2020

@CarlH Thank you for your response. I have juast one more question. The installation inastructions indicate that the bolts that hold the bumper assemblyshould be reused for the hitch installation. I have been advised that the bolts should be grade 8 bolts and just wanted tyo confirm if these conform to that standard. Do you know if the bumper assembly bolts are grade 8?

Reply

Jon G.

8/18/2020

Right off-hand I don't know 100% that they are grade 8 bolts but I would assume that is the case, especially since Curt says to reuse those bolts for their trailer hitch installation.

Reply

See All (5) Replies to Carl H. ∨

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

There isn't much difference at all between the etrailer Trailer Hitch #e63ZR to the Curt Trailer Hitch #C13417 for your 2020 Ford Ranger, so you aren't missing anything though it's smart to ask. The differences are just in the respective…

view full answer...

Answer 3

I have exactly what you need to install a 7-way trailer wiring harness on a 2001 Ford E-350. That said, they don't make a direct plug and play 7-way for this vehicle so you will need to start with a 4-way first like the T-One Vehicle Wiring…

view full answer...

Answer 4

Your concerns are understood, but consumers of aftermarket products are protected by the Federal Magnuson-Moss Warranty Act. This states that if something breaks on your vehicle and you take it in for warranty repair, the dealer must honor your…

view full answer...

Answer 5

We don't carry a crank handle specifically for the Coleman Tent Trailers, but we do have many cranks that may work depending on your specific camper. If you are looking for the crank to raise the tent of the camper, I believe what you are looking…

view full answer...

Answer 6

Tonneau covers and ladder racks can be compatible with each other when they do not use the same mounting points on the truck bed rails. Both tonneau covers and ladder racks can mount either inside the bed rails or on top of them. As an example, the…

view full answer...

Answer 7

I have a solution for you, but the Lomax Hard Tonneau Cover #A95FR mounts on top of the bed rails and will interfere with any ladder rack. The tonneau cover that I recommend going with is the BAKFlip F1 Hard Tonneau Cover - Folding #BAK772332. This…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 10

Yes, since your Winnebago 2108DS was pre-wired for a Voyager RV camera setups the #ASA37YR is the correct kit you'd want.

view full answer...

Answer 11

RV manufacturers have started running wiring and mounts for specific camera brands, i.e. Furrion or Voyager. The Voyager WiSight 2.0 Wireless Backup Camera System w/ Night Vision for Prewired RV #ASA24YR you were looking at mentions…

view full answer...