Replacement M12 Bolt, Washer, and Lock Washer for Thule Vertex Bike Rack 9029

Question

Question:

I lost the part that secures the 9029 bike rack to the trailer hitch so I think I just need the bolt that holds rack to hitch M12 in the manual with M12 flat washer and lock washer. Can I just purchase those? The only thing I saw was the set up with the big lock which I dont think I need.

asked by: Linda

0

Expert Reply:

The replacement parts you asked about for your (discontinued) Thule Vertex Bike Rack 9029 are part # 908-1240-54 for the M12 Bolt, part # 951-1224-54 for the Washer, and part # 956122159 for the Lock Washer.

The Thule Snug Tite Hitch Lock and Anti-Rattle Device # THSTL2 would work as well but if you don't want/need the lock you can use the parts mentioned above instead.

expert reply by: Jon G

0

Answer 1

The Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier TH665C (discontinued) comes with an anti-rattle hitch bolt but if you want to upgrade that to a locking hitch pin you just need the Thule Snug Tite Hitch Lock #THSTL2 which is…

view full answer...

Answer 2

Yes, the bolts of the etrailer Trailer Hitch Receiver #e98864 are M12-1.25 x 35mm bolts. So for a thread tap you will just need a 12 mm x 1.25 tap.

view full answer...

Answer 3

The washers that are included with trailer hitch #24819, are conical tooth washers similar to #01292006-020-01. You are correct, they are sort of bowl shaped. The tooth end goes towards the hitch. I have included a link to the installation…

view full answer...

Answer 4

We have the replacements for the knob of your Thule Apex XT, part #TH9024XT, here. For the knob itself, you will need the Replacement Locking Knob for Thule Bike Racks, part #TH79JV. I've linked to a video review of this below. Since you…

view full answer...

Answer 5

For me there is one clear choice between the two bike racks you asked about, and for one very particular reason - convenience. Due to how convenient it is, I definitely recommend the RidgeBack, which is the following part number: - Yakima RidgeBack…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Angelo, thanks for reaching out! The Replacement Hardware Bag #7520990001 won't work for your Thule T1 TH9041 bike rack. If you're needing to replace the anti-rattle hitch pin then the Thule Snug Tite Hitch Lock and Anti-Rattle Device…

view full answer...

Answer 8

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...

Answer 9

Yes, there is! It is the Draw-Tite item #76271. This hitch is custom fit for the 2024 Subaru WRX and bolts to it with included hardware. It is a class III hitch with a 2" receiver that has a 3,500 lbs towing capacity and a 525 lbs maximum tongue…

view full answer...

Answer 10

Thanks so much for the photos, they were very helpful, and based on that and the fact you mentioned it was from 2009, I am almost certain that what you have there is the Thule Roadway 914 bike rack. We do in fact have the correct 1-1/4" to…

view full answer...

Answer 11

I checked with my contact at Thule and verified that the Thule replacement hitch bolt you are looking for is part #908-1240-54. It is a 12 x 40mm hex bolt with a property class of 8.8. It should be installed with M12 washer, #951-1224-54, and M12…

view full answer...

Answer 12

There's not much of a difference in the 2" hitches available for the 2023 Toyota RAV4. The Draw-Tite item #DT82QR, Curt item #C13416, and etrailer item #e23ZR all look identical when installed. With this in mind, I recommend going with the…

view full answer...