How To Center The Steering Wheel After Installing Roadmaster Steering Stabilizer On Class A

Question

Question:

After mounting this what adjustments are needed to center your steering wheel with this.

asked by: Larry H

0

Expert Reply:

The only way to center the steering wheel is to test drive it after installation. If the vehicle is pulling after you have installed the Roadmaster Steering Stabilizer part # RM-RBK4-RSSA then loosen the bracket U-bolts at the tie rod and re position it. Tighten the bolts and test drive it once again, repeating the process until the proper adjustment is achieved.

expert reply by: Heather A

0

Jim

9/8/2020

So, how does one re-position the ubolt bracket, right or left when the stabilizer is under spring tension?

Reply

Jon G.

9/11/2020

Basically what happens is that you straighten up your steering wheel and then when you loosen up the U-Bolts the stabilizer will naturally center because of the tension. It shouldn't snap into place where it could be dangerous. Check out this installation video for another tip on how to help keep everything lined up.

Helpful Links

tv-install-roadmaster-reflex-steering-stabilizer-2016-tiffin-allegro-red-rm-rbk18-rssa.aspx

Reply

Answer 1

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 2

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 3

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 4

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 12

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

How To Center The Steering Wheel After Installing Roadmaster Steering Stabilizer On Class A

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching