Power Gear 500089 Replacement Control Panel

Question

Question:

Does # LC359259 replace #500089??

asked by: Bill

0

Expert Reply:

Yes the Replacement Lippert Components Power Gear Manual Leveling Control Kit part # LC359259 will replace the control panel and wiring for the Power Gear 500089 system.

expert reply by: Heather A

0

Answer 1

To replace your Power Gear controller #500457 you will need the Replacement Lippert Power Gear Manual Leveling Control Kit #LC359259. This will give you a new touchpad controller and the wiring necessary to work with your system.

view full answer...

Answer 2

The plug that includes the red wire from the Replacement Lippert Power Gear Manual Leveling Control Kit #LC359259 will plug into the back of the control panel and then the other end will plug into the connector coming off of the pump. The other…

view full answer...

Answer 3

To upgrade from your 500210 Power Gear Touch Pad you will in fact need the Replacement Lippert Components Power Gear Manual Leveling Control Kit #LC359259, which comes with a new touch pad, 8-pin harness and 6-pin harness. A 4-pin harness will not be…

view full answer...

Answer 4

You need the Replacement Motor with Mounting Plate for Kwikee Electric RV Steps #LC379608 for your 1999 Winnebago Brave. This is the motor that has been confirmed to replace your step motor on the Kwikee Series 32 steps.

view full answer...

Answer 5

I found an old wiring diagram for your now discontinued Power Gear 500210 control panel and it really helps show how things are supposed to work. There is a red wire running to the three jacks, the dump valve, and the float valve from the solenoid.…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Power Gear 500089 Replacement Control Panel

Product Page this Question was Asked From

Continue Researching