How Does SnowBear WinterWolf Plow Attach to 2003 Ford F-150

Question

Question:

I need instructions to mount my plow

asked by: Brian R

0

Expert Reply:

The correct mount kit to install the SnowBear WinterWolf Plow part # SB324-166 on your 2003 Ford F-150 depends on if you have 4WD or 2WD. If you have 2WD you'd need the kit part # SB397-104 or if you have 4WD you'd need # SB397-001.

These kits attach to the front frame of your truck and provide the correct attachment points for your SnowBear plow.

expert reply by: Jameson C

0

Answer 1

I contacted SnowBear and the SNB-SB200 plow needs a bracket fit part #SB397-105 to fit the 2006 F-150. Since the snow plow is an older model it did not come with the cross member so you do need the cross member to attach the plow to the truck part…

view full answer...

Answer 2

For your older Snowbear plow we have confirmed with them that the correct kit to convert it to fit a 2 inch hitch is the part #SB324-120 that you referenced. Then for a hitch for your 2015 Ram Big Horn you'd want the Curt #C31067 and you'd be…

view full answer...

Answer 3

The SnowBear Winter Wolf Snowplow #SB324-166 that you referenced is an excellent option to replace your older SnowBear plow. It mounts to your 1997 Dodge Dakota using the mounting bracket kit #SB397-028 that you also referenced. The mounting bracket…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

How Does SnowBear WinterWolf Plow Attach to 2003 Ford F-150

Products Referenced in This Question

Continue Researching