Correct Bayonet Flange with 3" Fitting for Waste Valve Body with Flexible Cable

Question

Question:

Valtera 3 inch remote cable dump valve do you have bayonett flanges so I can screw it right on my RV

asked by: Loran

0

Expert Reply:

If I'm understanding you correctly, you want a bayonet flange that will attach to this fitting and allow you to attach your RV hose. To accomplish this, you will want to use the 3" bayonet Flange # T1009 . If you need any ABS Cement you can add that with part # A05-0303 .

expert reply by: Erik B

0

Answer 1

For the 9/16 inch diameter shackle bolts included in the Redline Triple-Axle Trailer Hanger Kit #APTT5 referenced in your question, you will want 65 to 95 foot pounds of torque. This kit can be used to attach 6 leaf springs to your trailer frame. I…

view full answer...

Answer 2

There is not a specific torque spec for shackle bolts including the ones in the Tandem-Axle Trailer Hanger Kit part #APT3. They need to be secure but if they are too tight then the leaf springs will bind and cause problems in your trailer's…

view full answer...

Answer 3

There isn't a specific torque spec for shackle bolts like what come with the hanger kit part #APS5 you referenced. They need to be secure enough but if they are too tight then the leaf springs will bind and cause problems in your trailer's…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Correct Bayonet Flange with 3" Fitting for Waste Valve Body with Flexible Cable

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching