Is It Safe To Drive With The Edge EZ Tuner Switch Broken On 1999 Dodge Ram

Question

Question:

I had to the dashboard on my 1999 Dodge Ram. Long story short. In the process the 3 position switch to the tuners pulled apart. Is it safe to drive until I receive a replacement switch and cable. Also what position would the tuner be in with the switch in its disabled state.

asked by: Kendall L

0

Expert Reply:

I contacted Edge and the Edge EZ for the 1999 Dodge Ram part # EP30200 (which is the correct fit for your 1999 Dodge Ram) is safe to drive with the switch broken until you get the replacement. The Edge EZ will function in the tune that it is was adjusted to when the switch broke.

expert reply by: Heather A

0

Answer 1

The toggle switch with the Edge EZ programmer #EP30204 is needed to select the power level you want. If you do not want to mount the switch inside the vehicle then you could leave it under the hood as long as the cable and switch are protected and…

view full answer...

Answer 2

The replacement cable and switch for the Edge EZ part #EP30204 that you referenced is the part #EPHESW3-2.

view full answer...

Answer 3

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

Although the Tekonsha Prodigy P3 #90195 and Primus IQ #TK90160 electric brake controllers are very similar they do have some key differences as well. For one the P3 is designed to work with electric and electric over hydraulic brake systems. The…

view full answer...

Answer 12

There is not an exact torque specification to pre-load the bearings on a Dexter 8k axle. The spindle nut will need to be tightened by hand until finger tight and then turned another 1/4 of a turn with a wrench. This will be around 15 ft-lbs but you…

view full answer...

Is It Safe To Drive With The Edge EZ Tuner Switch Broken On 1999 Dodge Ram

Product Page this Question was Asked From

Continue Researching