Can the Edge EZ Programmer be Used without the Toggle Switch

Question

Question:

Do you need the toggle switch? Can u run on level 3 with out it ??

asked by: Jake

0

Expert Reply:

The toggle switch with the Edge EZ programmer # EP30204 is needed to select the power level you want. If you do not want to mount the switch inside the vehicle then you could leave it under the hood as long as the cable and switch are protected and not touching anything that gets hot like the block or exhaust as well as away from any moving parts. Then you could set the switch to the desired power level and then leave it alone.

expert reply by: Michael H

0

Answer 1

I am not sure which wire or step of the installation process you are referring to but I will walk you through the entire process below for future reference. In order to install the Edge EZ for Dodge Cummins 5.9L part #EP30203 on your 2003 Dodge Ram…

view full answer...

Answer 2

The replacement cable and switch for the Edge EZ part #EP30204 that you referenced is the part #EPHESW3-2.

view full answer...

Answer 3

For a 2003 Dodge Ram with a Cummins engine the needed Edge EZ module is the part #EP30203. What you sent in a picture of is for an older Cummins truck.

view full answer...

Answer 4

Here are the different power levels for the Edge EZ for Dodge Cummins 5.9L #EP30204 that you referenced: Level 1: 25 Horsepower - 50 Foot Pounds of Torque Level 2: 45 Horsepower - 75 Foot Pounds of Torque Level 3: 65 Horsepower - 150 Foot Pounds of…

view full answer...

Answer 5

Yes, you could run the level 3 of your Edge EZ for Dodge Cummins #EP30204 on your 2006 Ram with a Cummins while towing. That is what this product was intended to do. Give you additional power while towing.

view full answer...

Answer 6

I contacted Edge and the Edge EZ for the 1999 Dodge Ram part #EP30200 (which is the correct fit for your 1999 Dodge Ram) is safe to drive with the switch broken until you get the replacement. The Edge EZ will function in the tune that it is was…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Can the Edge EZ Programmer be Used without the Toggle Switch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching