How Much Bearing Preload Should be On Dexter 8k Axle
Question:
what is bearing preload for 8000 lb dexter oil bath hub/drum? thanks,
asked by: Don
Helpful Expert Reply:
There is not an exact torque specification to pre-load the bearings on a Dexter 8k axle. The spindle nut will need to be tightened by hand until finger tight and then turned another 1/4 of a turn with a wrench. This will be around 15 ft-lbs but you should not be using any sort of torque wrench for this. Once this is done you can then turn the hub ten or so times to seat the bearings and races but don't forget to back the spindle nut off some before you install the cotter pin and put the wheels on.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly for 8,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Oil Bath
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Oil Bath
- 25580
- 02475
- For 8000 lbs Axles
- 9/16 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Dexter Trailer Hub and Drum Assembly for 8,000-lb E-Z Lube Axles - 12-1/4" - 8 on 6-1/2
- Shop: Dexter Hydraulic Drum Brake Kit - Duo Servo - 12-1/4" - Left and Right Hand Assemblies - 8K
- Shop: Dexter Trailer Hub and Drum Assembly for 8,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Oil Bath
- Shop: Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2
- Shop: Dexter Trailer Hub and Drum Assembly - 8,000-lb Axles - 8 on 6-1/2 - Oil Bath
- Shop: Kodiak Disc Brakes - 11" Rotor - 8 on 6-1/2 - Raw - Leaf Spring - 10K Dexter and Lippert
- Search Results: hba16
- Search Results: 02475
- Search Results: 23~402~403
- Search Results: hub assembly
- Video: Review of Kodiak Trailer Brakes - Disc Brakes - K2R1058D11DAC
- Video: Review of Dexter Axle Trailer Brakes - Hydraulic Drum Brake Kit - 23-402-403
- Q&A: Torque Spec to Use for 8k Dexter Trailer Axles
- Q&A: How to Determine Correct Nev-R-Lube Bearing/Hub Assembly
- Q&A: Replacement Oil Bath Hub Drum for 8 on 6-1/2 Bolt Pattern on 8,000 lb Axle
- Q&A: Torque Spec for Installing Spindle Nut of Dexter Nev-R-Lube Spindle
- Q&A: How to Identify Correct Replacement Hub Based on Bearing Part Number or Spindle Dimensions
- Q&A: How Much Torque Is Needed To Pre-Load the Bearings On a Dexter Mobile Home Axle
- Search Results: hs381~8067
- Search Results: oil bath hubs
- Search Results: hs496~252
- Q&A: Brake Fluid Capacity of HydraStar Electric Over Hydraulic Actuator for Disc Brakes
- Video: Full Disc Brake Conversion Installation - 2020 Jayco Pinnacle Fifth Wheel
- Video: Dexter Axle Trailer Hubs and Drums - Hub - 8-288-3UC1 Review
- Video: Kodiak Trailer Brakes - Disc Brakes - K2R1058D11HD Review
- Video: HydraStar Electric Over Hydraulic Actuator Kit Installation - Flat Bed Trailer
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Overview of Lubricating Grease
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision