Internal Dimensions of Tekonsha Breakaway Battery Box

Question

Question:

C52090 The length measurement given was at the top opening. The box appears to be tapered. What is the inside dimension at the bottom where the battery sits? Ive attached photos of the battery dimensions I need the box for. Thanks

asked by: Duane

0

Expert Reply:

We do have a battery box though the Curt battery box you referenced does not have the correct length for your battery, which is just over 5-3/4" long. Instead, you will need the Replacement Clamp-On Battery Box for Tekonsha Trailer Breakaway Kit # TK2018 because it measures 5-15/16" long x 5-1/16" tall x 3-3/8" wide.

I have added a link to a video review of this battery box for you to check out as well.

expert reply by: Kyle S

0

click to enlarge

Answer 1

I ran out to the warehouse and pulled one of the battery boxes off the shelf, and took several measurements off of it. If you refer to the photo I have edited, you can see the dimensions of the outside of the box.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

To add a in-bed 7-way to your 2024 Chevy Silverado 2500 to make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item #C58FV. This harness puts a 4-way and 7-way…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

To install a brake controller like the #5504 that you referenced you only need to connect it to 4 wires. If you find more wires on your vehicle than would be needed to install the controller you wouldn't need to do anything with them. I attached…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 11

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Internal Dimensions of Tekonsha Breakaway Battery Box

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching