Required Roof Thickness For MaxxAir MA00-04000K RV Roof Vent Fan

Question

Question:

The roof of my pop up camper is 1/2” thick. Will this fan work?

asked by: Ryan A

0

Expert Reply:

The MaxxAir # MA00-04000K is intended for roofs 2-6 inches thick, so it wouldn't work well right out of the box for you. However, this is an extremely common issue that'e easily overcome by using some lumber to built a frame around the inside of the rough opening to increase the roof thickness. The frame also provides a good solid attachment point for the fan's mounting hardware. If you click the provided link, you can see a product description video featuring this fan.

expert reply by: Mike L

0

Answer 1

You will not need any extra parts to wire either the Dometic FanTastic Roof Vent #FV803350 or #FV807350 in place of your current fan. The MaxxFan Deluxe Roof Vent #MA00-07000K would be the route I would go thanks to its additional features. No matter…

view full answer...

Answer 2

From the edge of mounting flange that would sit on the roof to the inner plate that you would see inside the trailer is approximately 1-1/2". With it sitting down a 1/4" lower than the ceiling the mounting flange for the trim piece would…

view full answer...

Answer 3

To trim down the ceiling garnish of the MaxxAir Mini Trailer Roof Vent #MA00-03750 the easiest solution would be to measure how much you plan to cut off, mark where the cut needs to be made with a marker or pencil, and then use a hand saw to make the…

view full answer...

Answer 4

You'd be fine using two of the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote #MA00-07500K in your RV and not have to worry about one remote operating both fans. These require a clear line of sight from the remote to the fan so only…

view full answer...

Answer 5

MaxxFan does not offer a taller garnish than what comes with the MaxxFan part #MA00-07500K that you referenced but the included garnish can fit roof thicknesses that are up to 6-1/2 inches thick so you might check to see if it could fit. If you…

view full answer...

Answer 6

Yes the Ceiling Garnish for MaxxAir Maxxfan RV Roof Vent part #MA54FR will fit the MaxxAir vent that you have as long as it fits the 14x14 opening of a standard vent. The garnish fits a roof thickness up to 5-3/4".

view full answer...

Answer 7

Unfortunately the longest garnish available has a 6" long leg like the Ceiling Garnish for Fan-Tastic Vents Roof Vent - 6" Leg - 14-1/4" x 14-1/4" - White #FVK1060-81. Typically the garnishes are trimmed down to fit, but you…

view full answer...

Answer 8

The garnish that's included with the MaxxAir #MA00-04000K is 3 inches tall. I've confirmed this with our MaxxAir representative.

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Required Roof Thickness For MaxxAir MA00-04000K RV Roof Vent Fan

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching