Where Should I Take A 2018 Toyota Highlander To Have a Curt Hitch Installed

Question

Question:

Do you have any recommended shops / individuals in the Lenexa, KS 66227 area that will install the trailer hitch for an individual? All we want to use it for is to attach a bicycle carrier, no actual trailer pulling. Thanks,

asked by: Randall S

0

Expert Reply:

I would love to recommend a shop for you to use to install the Curt Trailer Hitch Receiver part # C13200 but this is not a service we offer. Although I cannot recommend an exact shop, I can tell you that the type of shop with the most experience installing trailer hitches is going to be an RV service center. Therefore, I recommend you reach out to a trusted RV service center in your area for installation. The professional install time is listed as 60 minutes so you can expect to pay about one hours labor but this rate will vary from shop to shop.

I have attached a photo of what the hitch will look like once installed.

expert reply by: Conner L

0

click to enlarge

Answer 1

Functionally speaking, there isn't a huge difference. The Curt #C56382 has a slightly lower capacity at 3 amps for circuit for stop/turn signals and 6 amps for taillights. The Tekonsha #118781 has a capacity of 5 amps per stop/turn circuit and…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Where Should I Take A 2018 Toyota Highlander To Have a Curt Hitch Installed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching