Where is AMG AMG102202 American Flag Hitch Cover Manufactured

Question

Question:

Where is the cover manufactured, what country?

asked by: Brad M

0

Expert Reply:

According to the good folks at AMG, the emblem itself use on the # AMG102202 american flag hitch cover is manufactured in Ft. Worth Texas, the backer portion that slides into the hitch is manufactured in China.

expert reply by: Mike L

0

Answer 1

I reached out to my contact at Camco to get the weight capacity for their Chair Rack for RV Ladders, #CAM51490. They said they don't have a published rating, but this chair rack has been tested to 60 lbs.

view full answer...

Answer 2

The Curt Cargo Carrier for 2" Hitches - Steel - Folding #C18152 has a 500 lb weight capacity so it absolutely has the needed capacity to hold your 250 lb holding tank. If you were asking about the capacity of the trailer hitch itself on your…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 10

Good news, I can help you find a tire for your Sundown Horse Trailer. The 205/90-15 is a close tire size to the 7.00-15. The closest size to a 7.00x15 tire that we offer would be a 225/75-15. One 225/75-15 tire that could work for you is the Kenda…

view full answer...

Answer 11

The Global Link RV Entry Door Locking Latch Kit #295-000019 that you referenced would be the correct fit for your 2010 Keystone Montana as this is a fit for standard RV doors like what your Montana has. I attached a review video link for this latch…

view full answer...

Answer 12

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Where is AMG AMG102202 American Flag Hitch Cover Manufactured

Product Page this Question was Asked From

Continue Researching