Is There a Repair Kit Available for a Fulton Boat Trailer Winch T1801Z1650

Question

Question:

I’m having a hard time finding an exact repair kit for my Fulton T1801Z1650 winch. The pawl in this kit looks like the pawl on mine. Is there any way you could tell me if it is compatible?

asked by: Matt N

0

Expert Reply:

I do have an option for you but the Fulton Boat Trailer Winch T1801Z1650 has been discontinued and there are no direct replacement parts available for this model. Therefore, you will have no other option but to replace the entire winch for which I recommend using the Fulton Single Speed Trailer Winch part # F142306 as it has the same 1,800 lb weight capacity and it comes with a 20' long strap.

expert reply by: Conner L

0

click to enlarge

Answer 1

What you have is a very standard boat winch with a 1,500 lb capacity and a nylon strap. For a similar winch we have the Fulton part #F142306 which has an 1,800 lb capacity and would easily bolt to the same mounts as what you have. Since it has a…

view full answer...

Answer 2

When you mention locking collar, I am led to believe that you might be describing a hammer blow-type coupler, like our part #BD028288. This type of coupler has a collar that would slide up, securing the jaws of the coupler in place over the trailer…

view full answer...

Answer 3

I have a solution for you. The Fulton Single Speed Trailer Winch - 10" Long Handle, w/ 20 FT Strap - 1,800 lbs, #F142306, is the winch I recommend for your application. This winch uses a 2-way ratchet system and has a solid drum design which is…

view full answer...

Answer 4

The 1402A winch is a Dutton Lainson and the only way we can help get a spring for that winch is with the part #DL70455.

view full answer...

Answer 5

I attached a picture that has all of the mounting hole dimensions of the Fulton winch part #F142400 that you referenced.

view full answer...

Answer 6

I would be happy to help you get the winch cable installed on your Fulton High-Performance Brake Winch #F143201, but unfortunately there is no online install instructions for this. To get the steel cable installed you will need to pass the cable from…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Is There a Repair Kit Available for a Fulton Boat Trailer Winch T1801Z1650

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching