Brake Assembly Replacement Recommendation for 1994 Eagle Boat Trailer

Question

Question:

I have a 1994 Eagle boat trailer with 3000 lbs axles and a 2 3/4” bolt pattern. 10” drums 2 1/4” pads which brake assembly do I need to order.

asked by: Kim

0

Expert Reply:

The brake assemblies part # 40716-15 that you referenced are exactly what you need. The size matches, the capacity is adequate, and the bolt pattern matches as well!

I attached a review video for this brake assembly set for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Knowing the inside diameter of the drum is the key piece of information we need; the brand of the assembly will not be a factor in determining what you will need to replace your hydraulic brakes. You mentioned your trailer's GVW, but it is…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Brake Assembly Replacement Recommendation for 1994 Eagle Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching