Solution for Atwood Landing Gear In Need of Repair Kit

Question

Question:

I have a Jayco 2009 32.5FBHS SUPER LITE CAMPER. Will this part fit my landing gear box that has Atwood mobil porducts on the outside with no numbers visible on it.

asked by: Lennie

0

Expert Reply:

I really wish we had a repair kit for your Atwood landing gear but we no longer have options for them since they are no longer around. Realistically your only option will be a new landing gear set like the # LG-1 which will easily replace what you have now.

expert reply by: Jameson C

0

Answer 1

I have a complete replacement landing gear option for you, but the Atwood number you provided is actually the tech bulletin number that goes over the technical specifications of the landing gear. Unfortunately since Atwood has gone out of business…

view full answer...

Answer 2

I went into our warehouse with a digital caliper to take the requested measurements for you. The Replacement Gear Kit for etrailer and Ram Sidewind Jacks - 2,000 lbs and 5,000 lbs #TJA-2000S-GR has an inner diameter of 0.5 inches and outer diameter…

view full answer...

Answer 3

The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do…

view full answer...

Answer 4

Yes, there is 15 teeth per each gear on the Replacement Gear Kit for etrailer and Ram Sidewind Jacks #TJA-2000S-GR. These gears have a thickness of 0.5", an OD of 1.36", and an ID of 0.5".

view full answer...

Answer 5

Yes, I attached a diagram you can use to install the #LC146059 that you referenced.

view full answer...

Answer 6

In the past we have had customers use the Replacement Gearbox part #LC276602, Lead Leg Leg Repair Kit part #LC146059, and Follow Leg Repair Kit part #LC146060 on the Atwood landing gear legs with success but it would be hard for me to confirm fit…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...