Height of the B&W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter

Question

Question:

What is the height of a companion turnover hitch for flatbed

asked by: Bernie

0

Expert Reply:

The B&W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter # BWRVK3050 has a fixed height at 10-1/2". I confirmed this with my contact at B&W.

expert reply by: Jon G

0

click to enlarge

Answer 1

The post of the #BWRVK3050 Companion 5th Wheel Hitch for flat bed trucks that installs into their Turnover Ball hitch is 4-1/8 inches long, and the slot in the post measures 3-1/2 inches long, as shown in the provided photo. The #BWRVK3050 is meant…

view full answer...

Answer 2

The base dimensions of the B and W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3050 is 18 x 18-inches and will install it in an opening that measures 20 x 20 x 4-inches deep. The recessed opening cannot be more than 4-inches…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 #LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Height of the B&W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching