Recommended Trailer Jack To Clear Tailgate With A-Frame Trailer
Question:
I have a 6’x10’ Tillman dump trailer 7,000lb capacity. I’m looking for a jack that will allow me to open my tailgate on a 2015 ram 2500. It has an A frame setup now but not opposed to welding on the side. Anything strong enough to hold 4 tons of weight when I need to remove trailer loaded and allow me to open tailgate when connected. Thanks
asked by: Ron
Expert Reply:
I do have an option for you but the tongue jack only needs to be rated for the tongue weight of your trailer which will only be around 10-15% of its loaded weight. Therefore, you are likely only going to need around a 700-1,000 lb weight capacity. The higher rated you go, the better off you will be but an 8,000 lb option would be far too much. In order to clear your tailgate while the trailer is attached you are likely going to need a side mount, swivel option. I recommend the Bulldog Round Pipe-Mount Swivel Jack part # BD178203 because all you will need to do is weld a pipe mount onto the side of the trailer and that would then give you not only plenty of capacity but also the ability to lower your tailgate with the jack in the stored position.
Please note, installing a side mount trailer jack on an a-frame trailer with a heavy tongue can lead to instability issues. That said, it might be a better option to use a longer ball mount like the Curt Class III Drawbar part # C45270 for example which has a 7,500 lb weight capacity and measures 13" from the center of hitch pin hole to the center of the ball hole.
Products Referenced in This Question
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- Swivel Jack
- 15 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Continue Researching
- Shop: Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Q&A: Looking for Shorter A-Frame Jack to Clear my Tailgate
- Q&A: Hitch Extension Recommendation to Allow Tailgate to be Down When Towing Travel Trailer
- Video: Bulldog Topwind Round A-Frame Jack Review
- Shop: Curt Weight Distribution Shank - 14" Long - 7" or 7-1/2" Drop - 1,500 lbs TW
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Bulldog Round, A-Frame Jack - Topwind - 15" Lift - 2,000 lbs
- Shop: Pro Series Round, A-Frame Jack w/ External Gearbox - Sidewind - 14" Lift - 2,000 lbs
- Shop: Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long
- Article: Trailer Wiring Diagrams
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Shop: Trailer Hitch
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Search Results: 25580
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Search Results: 68149
- Q&A: Seal With Dimensions to Replace 171255UC
- Shop: Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Video: Titan Trailer Brakes T2385200 Review
- Search Results: equalizer
- Article: How to Choose the Right Trailer Hitch Class
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Shop: Fifth Wheel Hitch
- Q&A: Recommended Dexter Suspension Kit 7753400
- Shop: Gooseneck Hitch