Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 For Keystone Fuzion

Question

Question:

Will this fit my 2017 Keystone Fuzion?

asked by: Mike C

0

Expert Reply:

The Replacement I-Beam Jack Bracket part # LC349975 is a direct replacement for Lippert Ground Control 3.0 Jacks part # LC358590 and part # LC675817. The bracket is ideal for eight inch and ten inch I-beams so if your I-beam is 8 inch or ten inch this should work fine for you.

expert reply by: Heather A

0

Answer 1

I attached a dimension picture I got from Lippert for the Replacement I-Beam Jack Bracket #LC349975 that you referenced.

view full answer...

Answer 2

This has been a topic of conversation we have had in the past and verified with the manufacturer, and they've confirmed that a bent/broken leg is not replaceable, unfortunately. The only solution is to replace the entire assembly with the Lippert…

view full answer...

Answer 3

Sounds like you have a Lippert Ground Control auto leveling system on your 2016 Highland Ridge Open Range like the #LC358590. For a replacement front leg you'd just need #LC362485 and you'd be set. The price for this is at the attached…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 8

We have actually spoken with Ventline regarding your model AS-13 M-VD0449 in the past and they have confirmed that the correct replacement cover is the part #BVD0449-A03 in Smoke or #BVD0449-A01 in White. The cover measures 14 inches x 14 inches and…

view full answer...

Answer 9

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 10

We have two options of replacement vent covers for the V2094 model, the white dome assembly, #BVD0449-A01, and the #BVD0449-A03 for smoke. These work for Ventline Ventadome roof vent models V2092, V2094, V2119, and V2128 after 2008. Pre 2008, please…

view full answer...

Answer 11

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 12

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement screen #BVD0434-31, the replacement lid #BVD0449-A01, and the replacement ceiling…

view full answer...