Distance From Hitch Pin Hole To Brace On the Curt Pintle Hook Mounting Plate C48341

Question

Question:

what is the measurement from center of mount hole to the point where diagonal support brace meets the bar ? the video says the distance from mount hole top front of plate is 10 inches, but need measurement to the support brace

asked by: Jay

0

Expert Reply:

The distance from the center of the hitch hole to the beginning of the brace on the Curt Pintle Hook Mounting Plate part # C48341 is 3". If you need more than this then we have the B&W Pintle Hook Mounting Plate part # BWPMHD14004 which measures 4-5/8" from the center of the hitch hole to the beginning of the brace.

expert reply by: Conner L

0

Answer 1

Great question. I have a solution for you: Blue Ox Trion Tow Bar - Car Mount - 2-1/2" Lunette Ring - 20,000 lbs #BX7520P. I recommend the blue ox if you need to handle 20,000 pounds. If you do not have a hitch receiver or pintle hook I…

view full answer...

Answer 2

If the gusset is what is interfering with the rear bumper on your 2015 Acura RDX with a 2 inch hitch check out the Forged Ball Mount #40331. This drawbar doesn't have any gussets that would interfere and has a distance of 9-1/4 inches from the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

The Blue Ox Adjustable Ball Mount with Pintle Hook for 2-1/2" Hitch #BLU25XR and the Curt #C45908 are identical. According to Blue Ox and Curt they don't make the parts for each other so in theory it is not the exact same part, just the same…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Distance From Hitch Pin Hole To Brace On the Curt Pintle Hook Mounting Plate C48341

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching