Length of the Bottom C-Channel for 54" Rhino-Rack Vortex Aero Crossbar

Question

Question:

What is the length mm of the C-channel on either side of the center piece of the 54inch 1375mm Vortex Crossbar RRVA137B?

asked by: Steve

1

Helpful Expert Reply:

The measurement that you asked for in your picture on the Rhino-Rack Vortex Aero Crossbar # RRVA137B is 300 mm.

expert reply by: Jon G

1

click to enlarge

Answer 1

I did see the review saying they used spacers, though that is the only time we have ever come across this, so I wouldn't say yes, spacers are going to be needed to use the Rhino-Rack system, which is the following part number: - Rhino-Rack Vortex…

view full answer...

Answer 2

The Rhino Rack crossbars like the part #RRVA137B that you referenced are 3-1/8" wide x 1-3/16" tall.

view full answer...

Answer 3

I was able to go to our test fit bays and use a digital dial caliper to measure the top channel on the Rhino Rack Vortex Aero Crossbars #RRVA126B-2, that with the SX Series Legs #RRSX100 are confirmed to fit your 2015 Toyota Sienna with factory…

view full answer...

Answer 4

I measured the widths of the c-channel on the Rhino Rack Vortex Aero Crossbars and the bottom width is 7/8 inches and the neck width is 7/16 inches. I have attached a photo showing these measurements for you to check out. As long as the t-bolts on…

view full answer...

Answer 5

I reached out to my contact at Rhino-Rack and she reported that the Rhino-Rack #RRRLT600 legs will fit into RTC tonneau cover channels. Then you will need the Rhino-Rack #RRVA180B cross bars to fit into those legs.

view full answer...

Answer 6

The top channel of the Rhino Rack crossbars like the #RRVA137B is right at 1/2 inch at the top opening and then 3/4 inch down in the lower portion of the channel.

view full answer...

Answer 7

The width of the C channel that connects the 54 inch Rhino-Rack Vortex Crossbar to the foot is 1 inch and the width of the opening is 1/2 inch. The depth of the channel is 5/8 inch.

view full answer...

Answer 8

Rhino Rack actually has a kit designed specifically for fitting the tracks of a RetraxPro XR ladder rack with the part number #RRVA180B-RRRLT600. This kit includes the feet you mentioned #RRRLT600 which fits the tonneau.

view full answer...

Answer 9

I went ahead and had a teammate pull the Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 54" #RRVA137B-2 from our warehouse. The channel-less solid space in-between the bottom channels of the crossbar measures 30-1/2 inches long. If you…

view full answer...

Answer 10

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 11

Thanks for reaching out! The Rhino-Rack roof rack for your 2022 Mazda CX-5 is a great selection that I know you'll be happy with, and it includes the parts you referenced: 46" Vortex Crossbars - #RRVA118B-2 RCL Legs - #RRRCL4 RCP Fit Kit -…

view full answer...

Answer 12

I spoke to Rhino Rack about using the Rhino-Rack RVP Roof Rack for Fixed Mounting Points part #RRRVP51 on a 2019 Mazda CX-9 and they stated you must use the forward and middle mounting points. The last mounting point is only used when there are three…

view full answer...

Length of the Bottom C-Channel for 54" Rhino-Rack Vortex Aero Crossbar

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching