Where to Mount Tekonsha Voyager in Interior of 2019 Toyota Tacoma TRD

Question

Question:

Where and how do I mount the actual controller in my 2019 Trd offroad Tacoma?

asked by: David S

1

Helpful Expert Reply:

I looked up an interior picture of your 2019 Toyota Tacoma and there's an open area in front of the gear shift under the HVAC controls which would be the best place to install the Tekonsha Voyager # 39510 with the custom install harness for your truck part # 3031-P.

expert reply by: Jameson C

1

Answer 1

The correct wiring adapter for the Prodigy P3 Brake Controller #90195 your 2019 Toyota Tacoma is the Tekonsha Custom Wiring Adapter #3031-P. You will only need to plug it in to the connector underneath and to the left of the steering column; it is…

view full answer...

Answer 2

Thank you for your purchase of the Tekonsha PowerTrac Electronic Brake Controller #39523. This will install in your 2019 Tacoma using the wiring adapter part #3031-P which connects between the controller and the plug-in port under your dash. Since…

view full answer...

Answer 3

In order to find the best replacement bearings and seals for your Harbor freight Trailer, you will need to remove the wheel and hub and pull the bearings, seals, and races off your spindle. I have attached a photo that shows where you can find the…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...