Rebuild Kit Recommendation for Roadmaster 500 Stowmaster

Question

Question:

Can I get my stowmaster 500 refurbished and whats the cost ? Thanks

asked by: MIKE K

0

Expert Reply:

For your older model Roadmaster Stowmaster the correct rebuild kit is the part # RM-910003-10. This comes with all new replacements for the components of your tow bar that tend to wear over time.

The price is available at the attached product link.

expert reply by: Jameson C

0

Answer 1

I did some checking and your 2006 Nissan Xterra with a manual transmission is flat-towable as-is so all you need is the flat towing components and you'd be set. So the first thing you need is a base plate kit to provide the tow bar connection…

view full answer...

Answer 2

For a rebuild kit for your Roadmaster Stowmaster you'd want the part #RM-910003-20 actually as the other part number you mentioned is not the complete repair kit.

view full answer...

Answer 3

You would need to get an autowlok repair kit, item #RM-910003-10, this will repair the locking portion of his tow bar, This will come with instructions and enough pieces to repair both arms, kit includes 2 pins, 2 springs, 2 new buttons, 2 new…

view full answer...

Answer 4

For your 2014 Nissan Xterra X Series, the Kat's Heaters Custom Engine Block Heater - Frost Plug Style - 120V - 400 Watts - 30 mm, #KH11412 will install in the left rear (driver's side) cartridge. I've attached a picture to…

view full answer...

Answer 5

For your 2008 Nissan Xterra, the Kat's Heaters Custom Engine Block Heater - Frost Plug Style - 120V - 400 Watts - 30 mm, #KH11412, will be installed in the left rear (driver's side). I've attached a picture to help.

view full answer...

Answer 6

The draw bar on the Roadmaster MX Base Plates, #RM-344-3B, for your 2008 Nissan Xterra measures 1-1/2 x 1-1/2 inches square. However, this product is designed for only for use in flat towing applications. Any use other than flat towing will void…

view full answer...

Answer 7

Yes, a 2006 Nissan Xterra with a manual transmission is flat-towable. The first thing you need is a base plate kit like the Roadmaster Direct Connect part #RM-344-3B that you referenced. In addition to the base plates, you will also need a compatible…

view full answer...

Answer 8

One end of the umbilical cord that comes with the Brake Buddy Stealth Supplemental Braking System part #HM39530 is a 7-blade round connection that connects to motor home's 7-way plug. The other end is a 7-flat connector that plugs into the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...