How To Find the Correct TorkLift GlowSteps for a 2010 KZ Durango Trailer

Question

Question:

I have a 2010 KZ Durango travel trailer. Has manufacturer steps on it. I was given 4 step Glow steps but they dont have any of the bracket system attached, just the steps. Can I purchase stuff I need to attach them to my camper??

asked by: Tonya M

0

Expert Reply:

It sounds like you have a set of the TorkLift GlowStep Revolution Scissor Steps but need both the mounting brackets and hardware to attach to them to your trailer. If that is the case then you are just going to want to replace the entire step as these are not replacement parts that TorkLift typically offers so they would have to be special ordered which is why the cost would exceed that of a new step.

In order to get you the correct set of TorkLift GlowStep Revolution Scissor Steps I would need to know both the width of your step mounting bracket and your doorway height. Once you can get me these two bits of info I can then confirm the correct TorkLift GlowStep Revolution Scissor Steps for you. For example, the TorkLift GlowStep Revolution Scissor Steps part # TLA8104 are for a 25-1/2" wide mounting bracket (most common) and work with an entry height of 32-1/2" - 44". I have attached a list of all these options for you as well.

expert reply by: Conner L

0

Answer 1

Installing the TorkLift GlowStep Scissor Steps #TLA7802-8000 on your truck bed camper will be similar to installing them on a trailer. The mounting bracket connects to the camper just under the doorway and the steps connect to the bracket. I've…

view full answer...

Answer 2

When the Lippert #LC791572 steps are properly installed with the threshold plate firmly against the outside threshold you should have no issues. The only thing we hear from customers is how much they love them! While you have your tools out you might…

view full answer...

Answer 3

Yes; there is a way to do this. In order to add a step to your TorkLift Glow Step #TLA7803 you can use the Single Add-On Step for TorkLift GlowStep Kits - 20" Long x 8" Deep #TLA7801. This adds a step in the middle and leaves the rest of…

view full answer...

Answer 4

Sounds like you'd want to go with a removable scissor setup like the Brophy Camper Steps part #AS24 which will need to be taken off it's mounting bracket between uses. This will give you total access to your trailer hitch when needed.

view full answer...

Answer 5

Both the Brophy #AS24 and the TorkLift #TLA7804 are easily removed when not in use- and it's actually recommended that you do so. Additionally, they both weigh in around 26-lbs total, so they're easy to move on and off; so they'd both be…

view full answer...

Answer 6

We do carry a repair kit for the Dutton-Lainson DL-1602A trailer winch. You can use Winch Ratchet Repair Kit, #DL70455, as long as your winch was made after 1999. This kit will also fit DL1402A and DL1602ADD made after 1999.

view full answer...

Answer 7

I spoke with the manufacturer to ensure the measurements were correct and found that the chart on the page for #LC432690 is incorrect. It does require 27-1/2" of space for the mounting brackets. Both the #LC432690 and #LC432696 will be too big…

view full answer...

Answer 8

Essentially it's how the two scissor steps store. The part #TLA7844 stores more like a traditional scissor step seen typically at the back of truck bed campers while the #TLA8004 stores more like what is seen on the side of campers. Since you…

view full answer...

Answer 9

The TorkLift Glow-Step scissor step assemblies #TLA7804-8000 and #TLA8103 are primarily intended for RV use but there will certainly be other applications where they will work just fine. The key is making sure you will not lose essential ground…

view full answer...

Answer 10

Since the Torklift Glowstep #TLA7804-8000 has an entry height range of 31 to 42 inches your height of 37 inches would work well.

view full answer...

Answer 11

Good news, I can help you find a wider step than the 24 inch LC341504. I've linked all the steps for you but if you look through the filters there should be a measurement column and there are sizes from 14 inches to 30 inches wide. The Lippert…

view full answer...

Answer 12

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

How To Find the Correct TorkLift GlowSteps for a 2010 KZ Durango Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching