Bug Screen for Atwood Furnace Vent 30578

Question

Question:

Valterra Bug Screen for Atwood AFMD Model RV Furnace Vents A10-1305VP will this cover work?

asked by: Keith F

0

Expert Reply:

The best way to find a screen for your Atwood Furnace Vent 30578 is to measure the opening. Atwood is no longer in business so exact replacement parts are not always available. The two best options we have for you are the Valterra Bug Screen part # A10-1305VP which measures 6.85" long x 5.1" tall x 2.16" deep or the Camco RV Insect Screen part # CAM42144 which measures 3-3/4" diameter x 1-1/3" tall.

expert reply by: Conner L

0

Answer 1

The Roadmaster Battery Charge Line for Motorhomes part #RM-156-75 is 30 feet long. It Includes 12-gauge wire, split wire loom, circuit breaker, and hardware

view full answer...

Answer 2

It is very normal for the 12V charge line on a vehicle to provide only the voltage that is being provided by the alternator that is not being used by the vehicle itself. The 3.5 volts is not normal but just 3.5 amps would be normal when the vehicle…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Bug Screen for Atwood Furnace Vent 30578

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching