7-Way Trailer Wiring Kit for 2015 Mercedes-Benz Sprinter

Question

Question:

In my case I am not replacing a damaged factory connector. My van never had trailer lights. Is this kit appropriate?

asked by: Gwyn

0

Expert Reply:

Yes, the Tekonsha 7-way kit part # TK22115 is exactly what you need. It is a 7-way kit designed to fit your 2015 Mercedes-Benz Sprinter that did not have the factory connector. This is what you'd need for a new install that didn't have any trailer wiring currently.

expert reply by: Jameson C

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #13358 installation instructions which I've attached state to torque all M12 fasteners to 79 lb-ft. If you don't have a torque wrench, I recommend the Powerbuilt #ALL944001…

view full answer...

Answer 3

The only possible option for your 2015 Freightliner 3500 with a 30-3/8 inch frame is a weld-on universal hitch, the Curt Curt Class V Universal Weld-on Receiver Hitch and Brackets with 10.865" Drop #15902. This has a crosstube that measures 44…

view full answer...

Answer 4

Your 2015 Freightliner Mercedes Sprinter 3500 with the 144 inch wheelbase and factory step bumper is indeed compatible with the Curt Trailer Hitch Receiver #13375. The brackets and step frame do fit together, as you'll remove the factory…

view full answer...

Answer 5

We do not recognize this connector that you have provided a picture for but we have a solution. We do not have an adapter to go between that plug and a 7-way connector. However you can create your own 7-way jack for your trailer to plug into. You…

view full answer...

Answer 6

As long as your 2019 Mercedes-Benz Sprinter 2500 doesn't have the 30-3/8" frame (measured outside to outside) then you can use part #75549 if you have the standard bumper. I have attached an installation video of this trailer hitch on a 2016…

view full answer...

Answer 7

Yes, the RVS Third Brake Light with Camera #RVS-1016 is a confirmed fit for your 2015 Mercedes Benz Sprinter and will work with the display.

view full answer...

Answer 8

We do have a trailer hitch fit for your 2016 Mercedes Benz Sprinter 2500 that has the factory step bumper. The Curt hitch part #13358 would be what you need. This fits either length wheelbase as well. In the picture I attached you can see the hitch…

view full answer...

Answer 9

You will need a universal receiver like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07 for your 2015 Mercedes Sprinter. We do not carry a custom fit receiver that fits your 30-3/8" wide frame. The Draw-Tite receiver can…

view full answer...

Answer 10

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 11

You can hard-wire in a brake controller, and it seems that there are not a lot of the Sprinter 3500 models that are pre-wired, at least from what I've seen in my research. I have not seen any reports that this isn't possible, and we even have…

view full answer...

Answer 12

Since your trailer has LED taillights we don't have a converter that will work. Normally we recommend the part #C56196 but this does not work with LED bulbs. Most likely have a converter already installed on the trailer wiring if it has been used…

view full answer...

7-Way Trailer Wiring Kit for 2015 Mercedes-Benz Sprinter

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching