Long Lasting Taillight Kit Recommendation for Boat Trailer

Question

Question:

tired of replacing trailer lights. What are the best most long lasting?

asked by: Brad

0

Expert Reply:

For a long-lasting option LEDs are the way to go as they rarely, if ever, fail. The LED Combination Tail Light Kit for Trailers under 80" Wide # TLL9RK that you referenced is a great option for this. The taillights assemblies are submersible which means they were designed to drain water and the lights themselves are LED which like I said means they'll last a very long time.

I attached an install video for this kit for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 2

The longest crossbar we have is the 80" Yakima CoreBar Crossbar #8880656 but for 8' you'd need a 96" crossbar. Usually when people mount a roof rack system to a truck bed camper like your Lance they will offset it to it's easier…

view full answer...

Answer 3

The front and rear Torklift tie downs you need for your 2006 Chevy Silverado 2500 short bed without steps and a factory hitch are the part numbers #TLC2205 and #TLC3205.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 8

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 11

To connect back up lights you need to have a 7-way trailer connector on both your trailer and tow vehicle. On a 7-way the reverse lights are powered by the center pin. To connect reverse lights to the trailer's 7-way you can use 16 gauge wire…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...