Will the Curt Ball and Plate Assembly Work with the Reese Friction Sway Control Kit

Question

Question:

Why does just the replacement plate #RP58062 at $ cost more than a complete Reese Friction Sway Control Kit code 83660 at $ Why would anyone buy just the plate when you can get a whole kit cheaper. No way a steel plate and ball cost that much to make. Would the more reasonably priced Curt #17201 at $ work on a 21ft Jayco Jay Flight SLX8 at around 5,000 pounds?

asked by: Mark

0

Expert Reply:

The Replacement Ball and Plate Assembly part # C17201 should work just fine for your Jayco Jay Flight SLX 8 whether you have theReese Friction Sway Control Kit part # 83660 or the Curt Friction Sway Control for Weight Distribution Systems part # 17200. We also have the Replacement Ball and Plate Assembly for Husky Sway Control System part # HT34842 as well which should work with either of the above two sway control bars.

In regards to pricing, these figures can and will fluctuate based on several factors such as supply, demand, competitor pricing etc. but I won't have an exact reason for you on any given day. I recommend you choose the most cost effective item you are comfortable with using.

expert reply by: Conner L

0

Dave S.

3/16/2020

Can I have a Reese sway control on one side and a Husky on the other.

Reply

Chris R.

3/17/2020

The different brand sway bars likely differ a bit both in terms of length and tension, so I wouldn't recommend using both on the same trailer. This could cause noticeable issues in performance, so I highly recommend sticking with the same brand/model for each side of the trailer.

Reply

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 10

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...

Answer 11

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 12

The "radio" fuse of your 2014 Honda CR-V will need to be pulled and replaced with the Roadmaster FuseMaster Fuse Bypass part #RM76511. This product will make it easy to deactivate this circuit, you will only need to flip a switch instead of…

view full answer...

Will the Curt Ball and Plate Assembly Work with the Reese Friction Sway Control Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching