Dexter 5200 lb Hub # 8-201 Grease Seal Recommendation

Question

Question:

What bearing seal fits the Dexter 5200 lb Torsion Axle? Drum is part number 8-201 and it takes a 12x2inch brake kit which Ive identified a replacement for. Just having trouble figuring out what seal fits it.

asked by: Steven F

0

Expert Reply:

The grease seal you need for your Dexter 5,200 lb hub part # 8-201-9UC3-EZ is the # GS-2125DL which has an inner diameter of 2.125 inch and an outer diameter of 3.376 inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Using the hitch extension will reduce the tongue weight capacity of the trailer by 50 percent. But if you have a 2 1/2 inch trailer hitch receiver and use the Titan hitch extension #RP45292 the tongue weight capacity will not be reduced. At the 24…

view full answer...

Answer 2

For a lock washer for your Dexter 5200 lb axle, you will need Washer, part #5-23. If you need a tang style washer, you will need part #5-101 The tang style washer is used on E-Z Lube spindles and functions the same as a cotter pin, but designed for…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...