Gauge Wire Recommendation for Powering Rooftop RV Fan

Question

Question:

What gage. wire do I need to use from the battery to a Hangs 12volt. Vortex 11 RV fan

asked by: Dan F

0

Expert Reply:

Most RV roof vent fans draw around 5 amps like the MaxxAir part # MA00-05100K that you referenced so going with at least a 12 gauge wire would be adequate which we offer as part # 12-1-1 by the foot.

expert reply by: Jameson C

0

Answer 1

The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White Item #MA00-05100K only requires 12 volt, 5 amp power to operate so based on this 12 gauge wire would be overkill but 16 gauge such as #DW02359-1 sold by the foot…

view full answer...

Answer 2

Yes, you can wire the Rear View Safety Cigarette Lighter Adapter #RVS-505 to your Fantastic Fan #FV802250. All Fantastic Fans, including #FV802250, use the same "pancake style" motor which draws 4 amps so in order for a portable power bank…

view full answer...

Answer 3

The MaxxFan Deluxe Roof Vent #MA00-05301K is a great option for venting air out of your camper. This unit (as well as all other standard roof vents) is designed to connect to a 12V DC power supply in your camper. The only way to power the roof vent…

view full answer...

Answer 4

The MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-06401K only draws 5 amps so you don't need to go crazy with the wiring gauge but I would still recommend 10 gauge like part #10-1-1 (sold by foot) as it's heavier than you'd ever need and will…

view full answer...

Answer 5

The gauge of the wiring of the Fan-Tastic roof vent part #FV802250 is 16.

view full answer...

Answer 6

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 9

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...

Answer 10

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hey Devon, does your RV roof vent wall control unit look like the #MA59FR? If so you have a MaxxFan Plus RV roof vent that was designed for wall control and for a replacement unit you would want the part #MA00-04500K to use a setup that would use…

view full answer...

Gauge Wire Recommendation for Powering Rooftop RV Fan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching