Fuse Block Power Connections to Install Brake Controller in 2001 Silverado

Question

Question:

There is power to the fuse for stud 1 and 2 but no power to them with the fuses in place. There is no continuity from the fuse to the studs also. Do I have to do some wiring under the fuse box to connect the fuse to the stud. I am trying to install a brake controller I purchased from you. thanks

asked by: Charles W

0

Expert Reply:

You can refer to the linked article concerning brake controller installation in a 1999-2006 Silverado to see the steps needed to activate power for brake controller installation. Under the heading "Step 2 - Under the Hood" there are photos to illustrate. Photo D shows the wires that need to be connected at the Accessory Fuse Block. The linked photo shows these too. Additional steps are detailed for you as well.

expert reply by: Adam R

0

click to enlarge

Answer 1

Under the hood of your 2001 Chevy Silverado, remove the cover on the power distribution box. If standing in front of the truck facing the motor, the brake controller fuse will be that last large one in the back left corner, see picture. But the brake…

view full answer...

Answer 2

So while I can't see your cart, I believe I get the gist of what you're trying to do in replacing the 7-way and pigtail of your 2002 GMC Sierra. What you can do is add a new twist-lock plug, like you mentioned, as well as a compatible 7-way…

view full answer...

Answer 3

Just to make extra sure, the red wire should be directly next to the blue wire on the harness. The black wire should be above (or below depending on how you are holding the connector) the blue wire. And the white wire should be in the opposite corner…

view full answer...

Answer 4

Selecting the correct Bearing Buddy bearing protector for your 8-lug hubs requires that you know the hub's bore where the grease cap (or Bearing Buddy) fits. This requires using a precision digital or dial caliper and measurement to the nearest…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 10

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 11

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 12

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Fuse Block Power Connections to Install Brake Controller in 2001 Silverado

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching