Ladder Rack Recommendation that Fits with Tonneau Cover for 2019 Ram 2500 Short Bed

Question

Question:

The following named system is compatible with above vehicle Code:TH43003XT-501EX and Extang EX62430

asked by: Norbert N

1

Helpful Expert Reply:

The only tonneau cover we can recommend as a guaranteed fit with the Thule TracRac Ladder Racks like the part # TH43003XT-501EX you referenced is the BAK Revolver like the part # BAK48203 that you also referenced. The Extang you mentioned most likely will not open without interference from either the rail kit or the uprights of the rack.

Both of these are a confirmed fit for your 2019 Ram 2500 short bed and would work great together!

expert reply by: Jameson C

1

Answer 1

The Adarac Aluminum Series Custom Truck Bed Ladder Rack - Aluminum - 500 lbs, part #A76FR, is the Adarac truck rack that fits your 2017 Ram 2500 with the 6 1/2' truck bed. I have included a product description link.

view full answer...

Answer 2

Some trucks like your 2018 Ram 3500 have them covered. All you have to do is cut the plastic part covering your stake pocket out. Then you can install the Adarac Aluminum Ladder Rack #A76FR.

view full answer...

Answer 3

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

Yes, the Thule TracRac SR Sliding Truck Bed Ladder Rack #TH57RV will fit your 2020 Ram 1500 with the 5'7" bed and no Ram box. Unfortunately, this rack is only available in the silver color. We do offer the TruXedo Elevate Truck Bed Rack…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

I have a solution for you Travis as Pace Edwards does not offer a contractor rack for your 2023 GMC Sierra 1500. Instead you can use the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-M-FMCA28A59 with the Thule TracRac SR…

view full answer...

Answer 9

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 10

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 11

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 12

Hi Ruben; thanks for the question, and while there is one rack for your 2023 Ford F-150 with a 6-1/2' bed compatible with the Pace Edwards UltraGroove Metal Retractable Hard Tonneau Cover #PE66UV, it does not have sides, and is part #TX84NV.…

view full answer...