Recommended Trailer Hitch for 2016 Hyundai Elantra GT Hatchback

Question

Question:

Hello! Which hitch would fit on a 2016 Hyundai Elantra GT? Im wondering if the hatch back model would need a different installation than the sedan.

asked by: Janet B

1

Helpful Expert Reply:

You are right that the GT (hatchback) version of your 2016 Hyundai Elantra does require a different hitch model than the Sedan. For the GT hatchback model we have both the Draw-Tite Class I # 24905 and the Curt # C11400 that are confirmed to fit.

Between the 2 options I recommend going with the Draw-Tite # 24905 because it offers a bit of an easier installation process and unlike with the Curt model it doesn't require the installation of an additional strap when using the hitch for a non-trailer load like a bike rack or cargo carrier. It will provide you with a 1-1/4 inch receiver and will use existing holes in the vehicle's frame for a no-drill installation.

One thing you will want to check on your Elantra is whether or not it was built in Korea, as this hitch will not fit those that were. To determine this all you need to do is check the manufacturer sticker on the door jamb or take a look at your VIN. If the second letter is an "M" then the vehicle was built in Korea.

I have attached the written installation instructions for the Draw-Tite hitch that you can check out. All the needed hardware is included. If you can tell me what you plan on using the hitch for I will be happy to make some additional recommendations. In the meantime I have attached a couple links that will take you directly to our available selection of Class I compatible bike racks and cargo carriers that you can look through.

expert reply by: Chris R

1

Answer 1

The light-duty Class I hitch #C11400 is a confirmed fit on the GT Hatchback version of the 2016 Hyundai Elantra. We have not had a local customer come in for an install of this particular hitch on your particular vehicle so we do not have the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Recommended Trailer Hitch for 2016 Hyundai Elantra GT Hatchback

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching