Automatic Dual Changeover Regulator to Use for Champion Generator 100264

Question

Question:

I have a Champion dual-fuel generator model 100264 that came with a hose and regulator for a single propane tank. I would like to buy an auto changeover regulator for dual tanks that will work with my generator. Can you help? Thanks.

asked by: Dale

1

Helpful Expert Reply:

The Camco Automatic Changeover 2-Stage Propane Regulator # CAM59005 is the exact part that you need to power your Champion generator. This has a built-in red/green gas gauge to show you when each tank is empty and it also allows you to safely replace each tank without interrupting the gas flow from the one that you are currently using to power your generator.

If you don't already have pigtails for your propane tanks then the Camco Propane Supply Hose # CAM59153 which has the male inverted flare is what you will want to use.

Attached are review videos for you to check out.

expert reply by: Jon G

1

Joe

11/4/2021

Champion 100297 dual fuel generator: Want to do a dual auto propane hookup and switch. Do I need the regulator, pigtail hose and a bracket? Generator will be sitting on the ground in the woods at a cabin site

Reply

Les D.

11/8/2021

I took a look at the owner's manual for your 100297 generator and it shows that it comes with a propane regulator and 3 foot hose. If you wanted to use two tanks with auto switching between the two tanks, you could use the JR Products # 37207-31525 auto change over regulator with mounting bracket, along with two pigtails such as the MB Sturgis # 100575-30-MBS. You will reuse the hose that runs from the regulator to the generator unless you need a longer one, in which case you can reach out to me again.

Reply

Answer 1

We do have a hose and regulator that you can use on your Champion 3500 Dual Fuel Generator model #100264. You can use the Camco Automatic Changeover 2-Stage Propane Regulator #CAM59005, which is a direct replacement for the regulator on your…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 5

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

The Titan Hitch Box Extension and Reducer for 2-1/2" Trailer Hitches, #RP45292, is a confirmed fit for your 2012 Chevrolet Silverado 2500 HD short bed with a Lance camper. This extension is specifically designed for your slide-in camper with the…

view full answer...

Answer 9

The Reese Titan Extension/Reducer you referenced, part #RP45292 would work great with the 2-1/2 inch Class V hitch on your Ram. As you mentioned, the extension has a 8K capacity when cut down to the 24 inch length, that will provide a 2 inch receiver…

view full answer...

Answer 10

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...

Answer 11

The longest extension available that will work with the factory trailer hitch receiver on your 2019 Chevrolet Silverado 1500 is the Draw-Tite Hitch Extender for 2" Hitch Receivers - 18" Long #HE18. You will need to measure from the center…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Automatic Dual Changeover Regulator to Use for Champion Generator 100264

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching