Why are Trailer Hub Oil-Bath Caps Always Plastic

Question

Question:

Is there a metal cap that is threaded to replace the plastic Kodiak caps?

asked by: Billy M

0

Expert Reply:

Oil bath caps that are threaded are always plastic like the part # RG04-230 that you mentioned. Them being plastic has the advantage that you can see through the cap to allow you to know that oil hasn't leaked out.

expert reply by: Jameson C

0

Answer 1

We do offer a grease cap for an oil bath hub that has a 2-7/8 inch diameter at the threads, part #RG04-230, however the total height of the cap is 1-3/4 inches. This is the closest thing we offer to the oil bath cap you referenced.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Why are Trailer Hub Oil-Bath Caps Always Plastic

Product Page this Question was Asked From

Continue Researching