Height of Equalizers Included in Tandem-Axle Trailer Hanger Kit # AP233-H248

Question

Question:

Hi. I cant seem to find the height in the description or video for the 5/34inch equalizer in the subject kit. Is it two inches? Thanks

asked by: Wayde

1

Helpful Expert Reply:

Yes, the equalizers included in the Tandem-Axle Trailer Hanger Kit # AP233-H248 measure 2 inches tall (from eye hole to eye hole on center). I have attached a diagram to assist.

expert reply by: Chris R

1

click to enlarge

Answer 1

Since you said your tires were rubbing I would go with a hanger setup that is a little taller like the part #AP233-H248 which has 3-1/4 inch front/rear hangers and 3-5/8 inch center. Also, while the 60/40 rule for axle placement is a great starting…

view full answer...

Answer 2

Front and rear springs hangers should be equally spaced around the center hanger and spring equalizer. It may be that your trailer was modified (if not originally built) with a different height center hanger and that might be how the spacing became…

view full answer...

Answer 3

The reality is that not every manufacturer makes their suspension kits to the same standard sizes. Some use taller hangers with wider equalizers and some might use a taller equalizer with a shorter center hanger. It really just comes down to the…

view full answer...

Answer 4

For a trailer suspension kit that comes with 5-3/4 inch equalizers you would want the part #AP233-H248 instead of the #APT5. Aside from that and the center hangers being slightly different to accommodate the different equalizers the kits are the…

view full answer...

Answer 5

The thickness of the steel of the Hanger part #28-5 is 3/16 of an inch thick. The only way to get 6 of these exact hangers is to order a quantity of 6 of them. The #H248 comes with a set of taller center hangers. Center hangers are taller because of…

view full answer...

Answer 6

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 7

Finding the correct MORryde equalizer kit will be pretty specific, so I cannot tell you which will be correct without knowing the wheel spacing and axle capacity, unfortunately. With that being said, if you have the trailer's VIN, you may be able…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

To determine the location for the front and rear hangers on your tandem axle trailer you will first need to make sure that you have the correct center point for your equalizer hanger. The center point of your equalizer hanger needs to be located…

view full answer...

Answer 10

It is always good practice to have at least 2 inches of space between your tires whether it is a tandem or triple axle trailer. The 2-1/2 inches that you have between your tires should be enough for you to travel safely. There isn't really a hard…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

The equalizers of the part #AP233 have bushings in them already. The leaf springs you would use these with would already have bushings as well most likely. Typically people do not need to buy bushings with this kit or with this kit plus leaf…

view full answer...

Height of Equalizers Included in Tandem-Axle Trailer Hanger Kit # AP233-H248

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching