Custom Brake Controller Wiring Harness for 2019 Jeep Grand Cherokee and Installation Location

Question

Question:

For your 2019 Jeep Grand Cherokee, the harness connection point is under the dash to the left hand side. I've attached a photo to help as well as a video of this installation. If you are using a Tekonsha Brake Controller like the Prodigy P3 # 90195 then you will use # TK93VR for your wiring harness. If you are using a Curt controller like # C51110 you will use harness # C51446. Finally if you are using a controller like the RedArc Tow Pro Elite # 331-EBRH-ACCV2, then you will use the pigtail adapter # 3045-S.

asked by: Joe

0

Expert Reply:

For your 2019 Jeep Grand Cherokee, the harness connection point is under the dash to the left hand side. I've attached a photo to help as well as a video of this installation. If you are using a Tekonsha Brake Controller like the Prodigy P3 # 90195 then you will use # TK93VR for your wiring harness. If you are using a Curt controller like # C74VV you will use harness # C51446. Finally if you are using a controller like the RedArc Tow Pro Elite # RED44FR, then you will use the pigtail adapter # RED77FR.

expert reply by: Jason S

0

click to enlarge

Joe

1/29/2019

For your 2019 Jeep Grand Cherokee, the harness connection point is under the dash to the left hand side. I've attached a photo to help as well as a video of this installation. If you are using a Tekonsha Brake Controller like the Prodigy P3 # 90195 then you will use # TK93VR for your wiring harness. If you are using a Curt controller like # C51110 you will use harness # C51446. Finally if you are using a controller like the RedArc Tow Pro Elite # 331-EBRH-ACCV2, then you will use the pigtail adapter # 3045-S.

Reply

Jason S.

1/29/2019

We haven't seen your 2019 model year yet, but my Tech contact at Curt confirms those locations mentioned. If you do not have the wiring, then you will need to use the hardwiring kit for your brake controller like # 5506 if you have a 7-way or # ETBC7 if you need to convert from a 4-way to a 7-way.

Reply

Answer 1

While the Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer - Up to 20' Long - Gray #AD97ZR is confirmed to fit your 2021 Winnebago Micro Minnie Travel Trailer, model 2108fbs, the spare tire might make for a tight fit since this cover…

view full answer...

Answer 2

Sounds like you installed your Tekonsha brake controller like P3 part #90195 using the included factory trailer wiring connector. Since you are seeing a short message on the controller that would indicate to me that you have probably wired the…

view full answer...

Answer 3

You will need a trailer brake controller since the factory tow package on your 2022 Jeep Grand Cherokee only includes the receiver and the trailer wiring needed for the lights. Luckily it also includes the wiring for the brake controller so you will…

view full answer...

Answer 4

The plug to connect the #3014-P harness in your 2019 Jeep Cherokee to is behind a black cover that is just to the left of the steering column right above where the carpeting ends. You need to remove the black cover. Check out the picture I attached.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 12

The Prodigy P3 trailer brake controller uses a 4-wire hookup. The white wire is to be grounded to the battery negative terminal; the black power wire connects to the battery hot terminal through a circuit breaker; the red wire takes in the brake…

view full answer...

Custom Brake Controller Wiring Harness for 2019 Jeep Grand Cherokee and Installation Location

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching