Oil Seal for Dexter 12K Heavy Duty Axle with Disc Brakes

Question

Question:

Is this what I need for dexter 12k oil bath with disc hubs? Is there a unitized seal available? Thanks

asked by: TJ

1

Helpful Expert Reply:

Yes, the Oil Seal part # 10-56 is exactly what you need for your Dexter 12K Heavy Duty axle with disc brakes. If you wanted to be absolutely certain you could measure the inner and outer diameter of the one you have now and it should be 3.125" and 4.500" respectively.

expert reply by: Conner L

1

Answer 1

For your 12,000 lb axles with Oil, you either have an oil cap or oil seal leaking. For the oil cap I recommend the Oil Cap Kit for 9K, 10K and 12K Axles #RG04-300. For the replacement oil seal, you most likely need #10-56 which has an inner diameter…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 7

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 8

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Oil Seal for Dexter 12K Heavy Duty Axle with Disc Brakes

Product Page this Question was Asked From

Continue Researching